RC-Model Klemm 25d Laser cut Kit
In the years around 1935, the Klemm 25 was certainly the most popular sports aircraft in Germany. This was particularly evident in 1935, when no less than 111 Klemm 25 of the d and e series took off for the German flight of 161 registered aircraft. The Klemm 25 has been one of the most popular modular models in the Krick range for many years.
It was therefore time to adapt this design to the latest production and construction methods. Thanks to the targeted use of laser technology, all plywood and balsa wood parts are designed in such a way that a plug-in construction has been created that is simple and self-explanatory, is a lot of fun and very quickly produces a beautiful, warp-free shell without any special aids.
Nevertheless, importance was still attached to the scale loyalty and the achievement of the exemplary flight characteristics of this classic.
Compared to the previous design, many model aircraft requests for modern design have been introduced. Now the wing centre section with landing gear is firmly connected to the fuselage and both wing halves are attached. The aileron servos are located in the wing. Furthermore, the entire cockpit area from the bonnet has been designed to be removable with a magnetic holder for optimum and convenient access to the RC area. With all these improvements, the model is still as light as its predecessor and has the same impressive flight characteristics as the original.
The kit contains all wooden parts cut out in the finest laser quality, all linkage parts, cockpit windows, chassis parts and wheels, the deep-drawn bonnet and the decal sheet with the inscription. A detailed illustrated building instruction makes the construction very easy.
Covering material, adhesives and paints are not included.
Technical Specifications
Scale 1:7
Wingspan 1859 mm
Length 1071 mm
Wing area 40,80 dm²
Elevator area 6,50 dm²
Flying weight approx. 2000 g
Wing loading approx. 43 g/dm²
Required accessories
Aricle-no
42304 Brushless drive set with motor, propeller and controller
-- LiPo-batterie 11,1V approx. 3000 mAh
79053 2x Mini servo 940D with metalgears (ailerons)
79053 2x Mini servo 940D with metalgears or similar Size (Rudder and Elevator)
44030 oder 44031 Speedbond withe glue 112 g oder 500 g
45670 UHU Endfest 300 33g glue
-- Bespannfolie Oracover light antikyellow
FIESELER Fi-156 STORCH
Dieser Nachbau des legendären "Storch" bereitet Freude mit seinen vorbildgetreuen Starts und Landungen und den außergewöhnlichen Langsamflugeigenschaften. Das Modell ist mit großen Landeklappen (4-Klappen-Flügel) und Vorflügeln ausgestattet, das Fahrwerk ist gefedert und dämpft somit auch unebene Wiesenstarts hervorragend ab. Vorgesehen ist das Modell für einen Antrieb durch Verbrennungsmotor, eine Elektrifizierung mit 20-26 Zellen ist aber ebenfalls möglich. Ein entsprechender Elektroeinbauplan wird mitgeliefert.
Das Modell ist weitestgehend in Holz aufgebaut. Für die Freunde von originalgetreuen Rippentragflächen wurde eine weitere Version des Baukasten mit lasergeschnittenen Rippenbauweise hergestellt. Alle Holzteile sind passgenau CNC-Lasergeschnitten und werden im Stecksystem zusammengesetzt und verklebt. Außerdem ist umfangreiches Zubehör und ein großer Dekorbogen enthalten. Dem Bausatz liegt eine deutsche Bauanleitung sowie ein ausführlicher Montageplan mit vielen perspektivisch dargestellten Baustufenzeichnungen bei.
Ersatzteil:
870146 Bausatz Rippentragfläche einzeln
Alternativ lieferbar:
870093 Baukasten Fieseler Storch mit Styro-Fläche
Die Styro-Kerne der Tragflächen sind mit einer weißen Balsa/ Gelcoat-Kombination beplankt, wobei diese gleich um die Nasenleiste mit herumgezogen wurde.
Technische Daten:
Spannweite: 2080 mm
Länge: 1280 mm
Fluggewicht: ca. 4800 g
RC-Funktionen: Höhe, Seite, Quer, Motor, Landklappen
empf. Motor: 7,5-10 ccm Zweitakt oder 15 ccm Viertakt
DUMAS Pilatus Porter R/C Model Airplane Kit
Truly one of the world's great flyers and the Dumas model of the Pilatus Porter is no different. Designed by Pat Tritle for electric R/C using affordable off the shelf components.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded cowl and spinner
Lightweight white tissue (Three sheets)
Wing: Two piece with center section, high mount placement Covering: Three sheets of white tissue Cowl: Vacuum molded plastic with molded in spinner, white in color
Landing Gear: Preformed wire .062" (1.6mm) diameter with .032" (0.81mm) diameter
Windows: One sheet acetate with pattern in manual for all windows
Rudder: Pull-pull style with horn and cables included
Kit including: All required balsa, three sheets white tissue, cowl, one small decal sheet, Two 1.6" (40mm) diameter lightweight foam main wheels and one 0.75" (19mm) plastic tail whee, one acetate sheet, hardware, instruction manual and two full-size plan sheets
FEATURES
Construction: Laser cut balsa
Wing: Two piece with center section, high mount placement
Covering: Three sheets of white tissue
Cowl: Vacuum molded plastic with molded in spinner, white in color
Landing Gear: Preformed wire .062" (1.6mm) diameter with .032" (0.81mm) diameter tail wheel wire
Wheels: Two 1.6" (40mm) diameter lightweight foam main wheels and one 0.75" (19mm) plastic tail wheel
Windows: One sheet acetate with pattern in manual for all windows
Rudder: Pull-pull style with horn and cables included
INCLUDES
All required balsa, three sheets white tissue, cowl, one small decal sheet, three wheels, one acetate sheet, hardware, instruction manual and two full-size plan sheets
REQUIREMENTS
Electric Motor: GWS IPS-DX2BB-1XCS Motor and Gear Drive or MPI EPU-4 drive unit
Radio: 3-channel with micro size receiver
Servos: Two micro size for rudder and elevator
Electronic Speed Control: 5A with BEC
Battery: 7.4V 700mAh Lithium Polymer
Propeller: 8x6 for electric application
Finish For Covering: Butyrate dope such as Midwest Aerogloss, lightweight Mylar covering can also be used, see COMMENTS
Building and field equipment
SPECIFICATIONS
Length: 27" (68.6cm)
Wingspan: 40" (101.6cm)
Wing Area: 285 sq in (18.38 sq dm)
Center of Gravity (CG): 1-5/8" (41mm) from the leading edge of the wing measured at the fuselage
Control Throws:
Elevator: up and down 5/8" (16mm)
Rudder: left and right 3/8" (19mm)
Airfoil: Flat bottom
COMMENTS
Do not use Ultra Cote or MonoKote covering. It is too heavy and will shrink too much damaging the lightweight structures.
Beginner model Habicht Lasercut Woodkit
Two models in a box. The two-axle glider for sailing and electric flying
Our completely new HABICHT, constructed in CAD and manufactured in CNC laser technology, is the ideal entry-level model for model aircraft. Even the experienced model builder will enjoy it. The construction of the model is deliberately kept very simple and is thus also easy to manage by the inexperienced model builder. All components are laser-cut with high precision. The building instruction with numerous pictures leads well through the construction.
The model is controlled by elevator and rudder, in the electric version also with motor control. The wing profile was developed from the profiles of modern high-performance models and gives HABICHT a high glide performance with low sink rate. Also the model penetrates well against stronger wind. The V-shape of the wing has been reduced to give the model excellent manoeuvrability, yet high inherent stability.
The hull is made of a few plywood and balsa wood parts. It is very robust and forgives many a hard landing. The canopy is removed via a magnetic lock so that there is convenient access to the flight battery (electric version) and the fittings. The wing is secured with rubber bands. It is a light ribbed construction, which is planked on the surface in the nose area. The tail units are constructed from lasered individual parts.
For the completion of the model only the ironing foil is necessary beside glue and a little tool (knives, pins, sandpaper, flat nose pliers and scissors) for covering.
The RC equipment of the glider requires a receiver battery with approx. 1,000 mAh and switch, the receiver with 2-4 channels and two servos with 15,5 mm width. Light motors with 26 or 28 mm diameter, a suitable BEC controller and a 3s-LiPo with approx. 1,300 mAh are intended to power the electric version - a very economical drive combination.
Thanks to the divided wing, the model is also easy to transport in a backpack, on a bicycle and in small cars. The glider can also be launched on the slope with the rubber rope in the plain. The electric version is also in no way inferior to the glider in terms of gliding characteristics.
HABICHT Electric flight
Wingspan: 1,680 mm
length: 1.050 mm
Tare weight: 430 g
Weight in flight: approx. 760 g
area: 32,34 qdm
Wing loading: 23.5 g/qdm
HABICHT Gliding
Wingspan: 1,680 mm
length: 1.035 mm
Tare weight: 460 g
Weight in flight: approx. 650 g
area: 32,34 qdm
Wing loading: 20.1 g/qdm
Recommended accessories
|42305| Drive set Habicht (electric motor version only) |79053| Midi Servo 2530D MG-BB Digital 2x
|44030| Speedbond/White glue DELUXE/UHU
|419001| Balsa knife with blades
|490050| Model building bumpers
|490190| Abrasive paper assortment
|492186| Flat nose pliers
Covering film (available in specialist shops) Transmitter and receiver (available in specialist shops) Receiver battery and switch (Only for the glider version - available in specialist shops)
Stinson Voyager Eletric Airplane Kit 40 inch Wingspan for DUMAS
Here is a beautiful model of the Stinson Voyager, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered Dumas Stinson Voyager Park Flyer Scale Kit. For beginning to intermediate modeler/fliers.
FEATURES
Construction: Laser cut balsa
Covering: Tissue, red in color
Wheel Pants: Vacuum molded
Cowl: Vacuum molded
Landing Gear: .041" (1mm) diameter wire requires bending
Wheels: Two foam 1.75" (44mm) diameter main, one plastic .75" (19mm) tailwheel
Decals: One sheet peel and stick vinyl
INCLUDES
Dumas Stinson Voyager Kit with covering tissue, decals, landing gear, three wheels, instructions, two plan sheets
REQUIREMENTS
Radio: 3-channel with micro receiver & two sub micro servos,
Motor: Speed 280 w/2.8:1 or higher gear drive, GPMG0300, GPMG0204
Electronic Speed Control: 5A with BEC, GPMM2005
Battery: 7.2-7.4 NiMH or LiPo
Battery Charger: LiPo compatible, GPMM3010
Propeller: 9x4.7 electric, GWSQ2018
Building and field equipment
SPECIFICATIONS
Wingspan: 40" (1016mm)
Length: 29" (737mm)
Wing Area: 218 sq in (14.08 sq dm)
Airfoil: Flat bottom, high wing placement
Center of Gravity: 1-13/16" (46mm) back from leading edge of wing at fuselage size
Control Throws:
Elevator: 5/8" (16mm)
Rudder: 3/4" (19mm)
Nieuport 28 WW I R/C Model Kit from DUMAS
Here is a beautiful model of the Nieuport 28, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered Dumas Nieuport 28 WWI Fighter Park Flyer Kit.
For beginning to intermediate modeler/fliers.
FEATURES
Construction: Laser cut balsa
Covering: Tissue, light and dark green in color
Cowl: Vacuum molded
Landing Gear: .062" (1.6mm) diameter wire, requires bending
Wheels: Two molded plastic, 3" (76mm) diameter'
Decals: Two sheets peel and stick vinyl
INCLUDES
Dumas Nieuport 28 Kit with covering tissue, decals, landing gear, wheels, instructions, two plan sheets
REQUIREMENTS
Radio: 3-channel with micro receiver & two sub micro servos,
Motor: Speed 280 w/2.8:1 or higher gear drive, GPMG0300, GPMG0204
Electronic Speed Control: 5A with BEC, GPMM2005
Battery: 2-cell (7.4V) 600mAh LiPo, GPMP0820
Battery Charger: LiPo compatible, GPMM3010
Propeller: 9x4.7 electric, GWSQ2018
Building and field equipment
SPECIFICATIONS
Wingspan: 35" (889mm)
Length: 26.5" (673mm)
Wing Area: 311 sq in (20.09 sq dm)
Airfoil: Flat bottom
Center of Gravity: 2.40" (61mm) back from leading edge of wing at fuselage size
Control Throws:
Elevator: 3/4" (19mm)
Rudder: 7/8" (23mm)
Erco Ercoupe R/C Model Airplane Kit from DUMAS
Here is a beautiful model of the Erco Ercoupe, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight. This is the radio controlled, electric powered Park Flyer Kit.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded Cowl
3x 41 mm Foam Wheels
Lightweight grey colored tissue
Kit including
Covering tissue, decals, landing gear, wheels, instructions, two plan sheets, two sheets peel and stick vinyl
Specifications:
Wingspan: 91,4 cm
Length: 63,2 cm
Wing area: 13,9 sq dm
Center of Gravity: 50 mm back from leading edge of wing at fuselage size
Control Throws- Elevator: 9.5 mm
Requires:
Assembly
Hobby knife
CA Glue
RC equipment radio: receiver, motor, ESC, servos, battery
Radio: 3-channel with micro receiver & one sub micro servo
Motor: Speed 280 w/2.8:1 or higher gear drive
Electronic Speed Control: 5A with BEC
Battery: 2-cell (7.4V)
LiPo Battery Charger
Propeller: 9x4.7 electric
Building and field equipment
Dragon Rapide - 42" Wingspan
Here is a beautiful model of the DH-89 Dragon Rapide, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered Dumas Dehavilland DH-89 kit
FEATURES
Construction: Hand selected laser cut balsa
Vacuum molded nose cone, windshield, engine cowls, nacelles and wheel pants
Rudder Control: Pull-pull cables
Aileron Control: Flexible control cables
Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Scale Rigging: Functional flying wires and tail braces
INCLUDES
All balsa, lightweight colored (gray) tissue covering two 2" (50.8mm) lightweight foam main wheels, CA hinges, rigging wire, control cables, instruction manual, three full-size plan sheets, acetate sheets for windows, and all hardware
to complete this kit
REQUIREMENTS
Two GWS IPS (GWSG2021) motors (3.5:1 gear ratio)
3 channel radio system (minimum)
4 micro servos
One 25A ESC w/BEC for brushed motors (GPMM2025)
2 cell 1200mAh LiPo battery (GPMP0835)
GWS 7x6 props, (GWSQ2015)
Building and field equipment
SPECIFICATIONS
Wingspan: 42" (1066mm)
Center of Gravity (CG): 1 5/8" (41.2mm) aft of the upper wing leading edge at the root
Control Throws:
Ailerons, Up and Down: 1/2" (12.7mm)
Elevator, Up and Down: 5/8" (15.9mm)
Rudder, Left and Right: 1" (25.4mm)
Taylorcraft Electric R/C Kit from Dumas
Here is a beautiful model of the Taylorcraft, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered Dumas Taylorcraft Park Flyer Kit.
FEATURES:
Construction: Hand selected laser cut balsa
Vacuum molded cowl
Rudder and Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Landing Gear: 1/16" diameter wire front, tail wire skid requires bending
INCLUDES:
All balsa, lightweight colored (blue and yellow) tissue covering two 1-3/4" (45mm) lightweight foam main wheels, tail wire skid, lightweight plastic tail wheel, CA hinges and all hardware to complete kit, instruction manual, two full-size plan sheets, acetate sheet for windows and vacuum molded cowl.
REQUIRES:
GWS IPS (indoor power system) motor with "A" ratio gear drive GWSG2023
3 channel radio system (minimum)
2 micro servos
5A ESC w/BEC GWSM2059
2 cell 700mAh LiPo battery
GWS 8x6 prop, GWSQ2017
Building and field equipment
SPECIFICATIONS
Length: 23-7/8" (606mm)
Wingspan: 40" (1016mm)
Wing Area: 272sq.in. (17.57 sq dm)
Airfoil: Flat bottom
Center of Gravity (CG): 1-7/8" (48mm) back from the leading edge of the wing
Control Throws:
Elevator, Up and Down: 3/4" (19mm)
Rudder, Left and Right: 7/8" (22mm)
Dumas Aeronca C-3 Park Flyer Kit
We are pleased to introduce the Aeronca C-3, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
1 Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
Rudder Control: Pull-pull cables
Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Landing Gear: 1/16 inch diameter wire front, .041 diameter wire rear, requires bending
FEATURES
Construction: Hand selected laser cut balsa
Vacuum molded nose cowl
Rudder Control: Pull-pull cables
Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Landing Gear: 1/16" diameter wire front, .041 diameter wire rear,
requires bending
INCLUDES
All balsa, lightweight colored (black and yellow) tissue covering two 1-3/4" (45mm) lightweight foam main wheels, CA hinges and all hardware to complete this kit, instruction manual, two full-size plan sheets, and acetate sheet for windows
REQUIREMENTS
GWS IPS (indoor power system) motor with "A" ratio gear drive
GWSG2023
3 channel radio system (minimum)
2 micro servos
5A ESC w/BEC GWSM2059
2 cell 700mAh LiPo battery
GWS 8x6 prop, GWSQ2017
Building and field equipment
SPECIFICATIONS
Length: 22" (559mm)
Wingspan: 40" (1016mm)
Wing Area: 329 sq.in. (21.25 sq dm)
Airfoil: Flat bottom, high wing placement
Center of Gravity (CG): 2.5" (63mm) back from the leading edge of the wing at the fuselage side
Control Throws:
Elevator, Up and Down: 3/4" (19mm)
Rudder, Left and Right: 1" (25mm)
DH-4 Park Flyer R/C Kit from DUMAS
Here is a beautiful model of the DH-4, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered DH-4 Park Flyer Kit.
FEATURES
Construction: Hand selected laser cut balsa
Vacuum molded cowl
Rudder and Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Landing Gear: 1/16" diameter wire front, tail wire skid
requires bending
INCLUDES
All balsa, lightweight colored (blue and yellow) tissue covering, two 2" (51mm) diameter plastic main wheels, tail wire skid, CA hinges and all hardware to comlete the kit, instruction manual, two full-size plan sheets, and vacuum molded cowling.
REQUIREMENTS
GWS IPS (indoor power system) motor with "A" ratio gear drive
GWSG2023
3 channel radio system (minimum)
3 micro servos
5A ESC w/BEC GWSM2059
2 cell 700mAh LiPo battery
GWS 8x6 prop, GWSQ2017
Building and field equipment
SPECIFICATIONS
Length: 25" (635mm)
Wingspan: 35" (889mm)
Wing Area: 329sq.in. (22.74 sq dm)
Airfoil: Flat bottom
Center of Gravity (CG): 1-13/16" (46mm) back from the leading edge of the TOP wing
Control Throws Elevator, Up and Down: 5/8" (11mm) Rudder, Left and Right: 3/4" (20mm)
Piper PA-20 Pacer Park Flyer Kit vrom DUMAS
Here is our new model of a Pacer, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered Dumas Piper PA-20 Pacer Park Flyer Kit.
FEATURES
Construction: Hand selected laser cut balsa
Vacuum molded nose cowl
Rudder Control: Pull-pull cables
Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Landing Gear: 1/16" diameter wire front, .041 diameter wire rear,
requires bending
INCLUDES
All balsa, lightweight colored (black, white and red) tissue covering two 1-3/4" (45mm) lightweight foam main wheels, one 3/4" (19mm) lightweight plastic tail wheel, CA hinges and all hardware to complete this kit, instruction manual, two full-size plan sheets, acetate sheet for windows
REQUIREMENTS
GWS IPS (indoor power system) motor with "A" ratio gear drive
GWSG2023
3 channel radio system (minimum)
3 micro servos
5A ESC w/BEC GWSM2059
2 cell 700mAh LiPo battery
GWS 9x7 prop, GWSQ2019
Building and field equipment
SPECIFICATIONS
Length: 27" (686mm)
Wingspan: 40" (1016mm)
Wing Area: 272 sq.in. (17.57 sq dm)
Airfoil: Flat bottom, high wing placement
Center of Gravity (CG): 2.5" (63mm) back from the leading edge of the wing at the fuselage side
Control Throws:
Elevator, Up and Down: 9/16" (14mm)
Rudder, Left and Right: 15/16" (23.5mm)
Tiger Moth - 35" Wingspan
By popular request we have developed an electric R/C version of our Tiger Moth. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
FEATURES
Construction: Hand selected laser cut balsa
Vacuum molded cowl and spinner
Rudder and Elevator Control: Wire pushrod
Servo Placement: Mounted in rails on fuselage
Landing Gear: 1/16" diameter wire front, tail wire skid
requires bending
INCLUDES
All balsa, lightweight colored (black and white) tissue covering two 1-3/4" (45mm) lightweight foam main wheels, tail wire skid, lightweight plastic tail wheel, CA hinges and all hardware to complete kit, instruction manual, two full-size plan sheets, acetate sheet for windows and vacuum molded cowl and spinner
REQUIREMENTS
GWS IPS (indoor power system) motor with "A" ratio gear drive
GWSG2023
3 channel radio system (minimum)
3 micro servos
5A ESC w/BEC GWSM2059
2 cell 700mAh LiPo battery
GWS 9x7 prop, GWSQ2019
Building and field equipment
SPECIFICATIONS
Length: 25" (635mm)
Wingspan: 35" (889mm)
Wing Area: 352sq.in. (22.74 sq dm)
Airfoil: Flat bottom
Center of Gravity (CG): 3-7/16" 87.5mm) back from the leading edge of the TOP wing
Control Throws:
Elevator, Up and Down: 1/2" (13mm)
Rudder, Left and Right: 1" (25.5mm)
Waco ARE - 35" Wingspan
Another rare subject is our laser cut model of the famous Waco ARE. A proven electric R/C flyer designed by Pat Tritle to use off the shelf flying packages.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
FEATURES
Construction: Laser cut balsa
Wing: Two piece with center section, high mount placement
Covering: Two sheets of red and two sheets of white tissue
Cowl: Vacuum molded plastic, white in color
Wheels: Two 1.75" (45mm) diameter lightweight foam main wheels and one 0.75" (19mm) plastic tail wheel
Windows: Three sheets acetate with pattern in manual for all windows
INCLUDES
All required balsa, One sheet of yellow tissue, cowl, one fake engine decal, two wheels, one sheet, hardware, instruction manual and two full-size plan sheets.
REQUIREMENTS
Electric Motor: GWS "A" or MPI EPU-6 drive unit
Radio: 3-channel with micro size receiver
Servos: Two micro size for rudder and elevator
Electronic Speed Control: 5A with BEC
Battery: 7.4V 700mAh Lithium Polymer
Propeller: 9x7 for electric application
Finish For Covering: Butyrate dope such as Midwest Aerogloss, lightweight Mylar covering can also be used, see COMMENTS
Building and field equipment
SPECIFICATIONS
Wingspan: 35" (889mm)
Center of Gravity (CG): 2-7/16"(62mm) from the leading edge of the
wing measured at the fuselage
Control Throws:
Elevator: up and down 3/4" (19mm)
Rudder: left and right 5/8" (16mm)
Airfoil: Flat bottom
COMMENTS
Do not use Ultra Cote or MonoKote covering. It is too heavy and will shrink too much damaging the lightweight structures.
Waco YMF-5 R/C Parkflyer Kit from DUMAS
Here is a beautiful model of the Waco WMF-5, designed by Pat Tritle. Designed to use stock off the shelf flying hardware for easy affordable flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
FEATURES
Construction: Laser cut balsa
Covering: Tissue
Wheel Pants: Vacuum molded
Cowl/Radial Engine: Vacuum molded (non-functional)
Landing Gear: .041" (1mm) diameter wire requires bending
Wheels: Two foam 1.75" (44mm) diameter main, one plastic .75" (19mm) tailwheel
Windshield: Flat plastic sheet
Decals: Two sheets with gold accents marked for accurate placement
INCLUDES
Dumas Waco YMF5 Biplane Kit with covering tissue, decals, landing gear, three wheels, instructions, two plan sheets
REQUIREMENTS
Radio: 3-channel with micro receiver & two micro servos
Motor: Speed 280 w/2.8:1 or higher gear drive, Dumas recommends the
Maxx brand motor which we do not carry
Electronic Speed Control: Compatible with selected motor
Battery: 3-cell (11.1V) 640mAh LiPo
Battery Charger: LiPo compatible, GPMM3010
Propeller: Contact Dumas for recommendation
Building and field equipment
SPECIFICATIONS
Wingspan: 35" (889mm)
Length: 25" (635mm)
Wing Area: 329 sq in (41.02 sq dm)
Center of Gravity: 3.2" (81mm) back from leading edge of wing at fuselage size
Motor Offset: 1° down thrust, 2° right thrust
Control Throws:
Elevator: .6" (15.2mm)
Rudder: 1.2" (30mm)
Bird Dog - 40" Wingspan
A beautifully laser cut model of the popular L-19 Bird Dog. Engineered specifically for electric R/C by designer Pat Tritle to use off the shelf flying packages.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
FEATURES
Construction: Laser cut balsa
Wing: Two piece with center section, high mount placement
Covering: Two sheets of red and two sheets of white tissue
Cowl: Vacuum molded plastic, white in color
Landing Gear: Preformed wire .062" (1.6mm) diameter with .032" (0.81mm) diameter tail wheel wire
Wheels: Two 1.75" (45mm) diameter lightweight foam main wheels and one 0.75" (19mm) plastic tail wheel
Windows: Three sheets acetate with pattern in manual for all windows
Rudder: Pull-pull style with horn and cables included
INCLUDES
All required balsa, two sheets red and two sheets white tissue, cowl, two decal sheets, three wheels, three acetate sheets, hardware, instruction manual and two full-size plan sheets
REQUIREMENTS
Electric Motor: GWS "A" (IPS-DX2BB-AXCS) or MPI EPU-6 drive unit recommended per Dumas
Radio: 3-channel with micro size receiver
Servos: Two micro size for rudder and elevator
Electronic Speed Control: 5A with BEC
Battery: 7.4V 700mAh Lithium Polymer
Propeller: 9x7 for electric application
Finish For Covering: Butyrate dope such as Midwest Aerogloss, lightweight Mylar covering can also be used, see COMMENTS
Building and field equipment
SPECIFICATIONS
Length: 27" (68.6cm)
Wingspan: 40" (101.6cm)
Wing Area: 215 sq in (13.89 sq dm)
Motor Placement: Offset 1.5° right thrust
Center of Gravity (CG): 1-7/8" (48mm) from the leading edge of the wing measured at the fuselage
Control Throws:
Elevator: up and down 3/4" (19mm)
Rudder: left and right 7/8" (22mm)
Airfoil: Flat bottom
COMMENTS
Do not use Ultra Cote or MonoKote covering. It is too heavy and will shrink too much damaging the lightweight structures.
Pietenpol - 36" Wingspan
This is our newest entry in electric R/C. Our version of The Pietenpol was taken right from the 1930's magazine plans. This laser cut kit is designed for three channel R/C flight.
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
FEATURES
Classic 1930's style model of a homebuilt "kit" plane designed by B.H. Pietenpol
INCLUDES
Laser cut balsa and birch ply parts, carbon fiber struts and supports foam tires, hinges, aluminum tubing, plans, instructions
REQUIREMENTS
Glue- CA, white or cellulose acetate butyrate (SigMent)-not carried
Hobby knife
Silkspan, Japanese tissue or other lightweight covering and adhesive
Control cables (4-6 lb nylon test or Kevlar, or DuBro pull-pull wire)
Electric motor with battery pack (Faulhaber DC-117 and 1524 gearbox
is recommended with 9V Ray-O-Vac NiMH battery-items not carried
3-Ch radio system and servos
Electronic Speed Control with BEC
SPECIFICATIONS
Wingspan: 36" (914mm)
Length: 24" (610mm)
Wing area: 230 sq in (14.86 sq dm)
Flying Weight: 6-7oz (170-198g)
COMMENTS
This kit is designed from a classic 1932 plans found in the FLYING AND GLIDER PLANS MANUAL. This kit is for the more advanced modeler, and is intended for flying in low wind conditions due to the lightweight.
35 inch Spad XIII Electric DUMAS
This is a beautiful model of the SPAD XIII, designed by Pat Tritle. Over 150 Laser Cut parts in the kit. Designed to use stock off the shelf flying hardware for easy affordable flight
Kit features:
Laser cut parts
Hand-selected balsa
Full size plans
Step-by-step instructions
Vacuum-molded parts
Lightweight colored tissue
This is the radio controlled, electric powered Dumas Spad XIII Park Flyer Scale Kit. For beginning to intermediate modeler/fliers.
FEATURES
Construction: Laser cut balsa
Covering: Tissue, red in color
Cowl: Vacuum molded
Hub Caps: Vacuum molded-for inside and outside of wheels
Landing Gear: .062" (1.6mm) diameter wire, requires bending
Decals: One sheet peel and stick vinyl
INCLUDES
Dumas Spad XIII Kit with covering tissue, decals, landing gear wire cowl, hub caps instructions, two plan sheets and interplane thread rigging
REQUIREMENTS
Radio: 3-channel with micro receiver & two sub micro servos,
Motor: Speed 280 w/2.8:1 or higher gear drive, GPMG0300, GPMG0204
Electronic Speed Control: 5A with BEC, GPMM2005
Battery: 2 cell 1200mAh LiPo battery (GPMP0835)
Battery Charger: LiPo compatible, GPMM3010
Wheels: 3" ultra light weight, GWSQ2204
Propeller: 9x4.7 electric, GWSQ2018
Building and field equipment
SPECIFICATIONS
Wingspan: 35" (889mm)
Length: 26.75" (679mm)
Wing Area: 400 sq in (25.84 sq dm)
Airfoil: Flat bottom
Center of Gravity: 2.25" (57mm) back from leading edge of top wing at fuselage size
Control Throws:
Elevator: 3/4" (19mm)
Rudder: 1-1/4" (32mm)